पाठ 1रनिंग-इन और इंजन परीक्षण प्रक्रियाएं: नो-लोड, क्रमिक लोडिंग, कंपन मापन, और तेल प्रणाली जांचओवरहॉल्ड इंजनों के रनिंग-इन और परीक्षण को कवर करता है, जिसमें नो-लोड जांच, चरणबद्ध लोडिंग, कंपन निगरानी, और तेल प्रणाली सत्यापन शामिल है। शिक्षार्थी डेटा लॉग करने और सेवा के लिए सुरक्षित तत्परता की पुष्टि करने का अभ्यास करते हैं।
Pre-start checks and priming proceduresInitial no-load start and safety monitoringIncremental loading and parameter loggingVibration and noise checks during run-inOil pressure, flow, and contamination checksFinal inspection and test report completionपाठ 2कंपन विश्लेषण मूलभूत: आवृत्ति, आयाम, कारण, और हैंडहेल्ड उपकरणमरीन फिटर के लिए कंपन विश्लेषण का परिचय देता है, जिसमें मूल शब्दावली, सामान्य कंपन स्रोत, और हैंडहेल्ड मीटर का उपयोग शामिल है। शिक्षार्थी आवृत्ति और आयाम पैटर्न को असंगठन, असंतुलन, और दहन मुद्दों से जोड़ते हैं।
Frequency, amplitude, and phase explainedCommon engine and shaft vibration sourcesRecognizing imbalance and misalignment signsTorsional and combustion-related vibrationUsing handheld vibration meters onboardTrend logging and alarm threshold settingपाठ 3गैसकेट, स्टड, और टॉर्क प्रथाएं: सतह सफाई, टॉर्क पैटर्न, और टॉर्क रिंच उपयोगगैसकेट और स्टड की सही हैंडलिंग, सतह तैयारी, टॉर्क पैटर्न, और टॉर्क रिंच उपयोग को समझाता है। सिलेंडर हेड और मैनिफोल्ड कार्य के दौरान रिसाव, विकृति, और फास्टनर विफलता को रोकने पर जोर दिया गया है।
Surface cleaning and flatness verificationGasket selection, handling, and positioningStud inspection, renewal, and lubricationTorque patterns and staged tighteningUsing and calibrating torque wrenchesRetorque procedures after initial runningपाठ 4सिलेंडर, लाइनर, और पिस्टन क्राउन के लिए दृश्य और बोरस्कोप निरीक्षण तकनीकेंसिलेंडर, लाइनर, और पिस्टन क्राउन की दृश्य और बोरस्कोप निरीक्षण पर केंद्रित। शिक्षार्थी पहनाव पैटर्न, जमा, दरारें, और स्कफिंग की पहचान करते हैं, और निष्कर्षों को दहन गुणवत्ता, स्नेहन, और शीतलन मुद्दों से जोड़ते हैं।
Lighting, access, and safety precautionsReading liner wear, polishing, and scuff marksRecognizing crown burning, erosion, and crackingIdentifying carbon buildup and wet stackingBorescope setup and image interpretationDocumenting findings for maintenance planningपाठ 5मध्यम-गति डीजल इंजन संचालन और दहन गतिशीलता के मूलभूतमध्यम-गति मरीन डीजल के संचालन सिद्धांतों को कवर करता है, जिसमें वायु हैंडलिंग, ईंधन इंजेक्शन, दहन चरण, और लोड प्रतिक्रिया शामिल है। दहन गतिशीलता के कुशलता, उत्सर्जन, और घटक तनावों को प्रभावित करने पर जोर दिया गया है।
Engine cycle review and timing diagramsAir charging, scavenging, and turbochargingFuel injection stages and spray formationIgnition delay and controlled combustion phaseEffects of load, speed, and fuel qualityCombustion issues: smoke, misfire, and rough runningपाठ 6क्लियरेंस मापन: वाल्व लैश, गाइड पहनाव, पिस्टन-टू-सिलेंडर क्लियरेंस, और लाइनर रनआउट मापनवाल्व लैश, वाल्व गाइड पहनाव, पिस्टन-टू-सिलेंडर क्लियरेंस, और लाइनर रनआउट मापने का विवरण देता है। सही उपकरण, मापन बिंदु, रिकॉर्डिंग विधियां, और निर्माता सहनशीलताओं के खिलाफ परिणाम व्याख्या पर जोर दिया गया है।
Selection and care of measuring instrumentsSetting and checking valve lash hot and coldMeasuring valve stem and guide clearancePiston skirt and ring land measurementsPiston-to-cylinder clearance assessmentLiner runout and ovality measurement stepsपाठ 7सिलेंडर हेड पुनर्संयोजन: वाल्व टाइमिंग, इंजेक्टर सीटिंग, इंजेक्शन पंप टाइमिंग जांचओवरहॉल के बाद सही सिलेंडर हेड पुनर्संयोजन को समझाता है, वाल्व टाइमिंग, इंजेक्टर सीटिंग, और इंजेक्शन पंप टाइमिंग जांच पर केंद्रित, उचित दहन, सुरक्षित स्टार्टिंग, और मरीन डीजल इंजनों की दीर्घकालिक विश्वसनीयता सुनिश्चित करने के लिए।
Pre-assembly cleaning and component identificationSetting camshaft and crankshaft reference marksValve timing alignment and verification stepsInjector seating, torque, and leak checksInjection pump timing and phasing checksPost-assembly rotation and interference checksपाठ 8सिलेंडर हेड हटाने की प्रक्रिया: तैयारी, क्रम, और सुरक्षित लिफ्टिंगमरीन डीजल पर सुरक्षित, चरणबद्ध सिलेंडर हेड हटाने का वर्णन करता है। विषयों में तैयारी, अलगाव, ढीला करने का क्रम, लिफ्टिंग गियर चयन, और सीलिंग सतहों तथा घटकों को क्षति से बचाना शामिल है।
Pre-removal checks and system isolationDraining fluids and disconnecting auxiliariesBolt loosening sequence and patternRigging, slings, and lifting point selectionGuiding, landing, and storing cylinder headsPost-removal inspection of deck and studsपाठ 9ध्वनिक/नॉक निदान: डेटोनेशन, पिस्टन स्लैप, और बेयरिंग नॉक को अलग करनाअसामान्य इंजन ध्वनियों को पहचानने और उन्हें दोषों से जोड़ने का शिक्षण करता है। स्थान, लय, तीव्रता, और संचालन स्थिति का उपयोग करके डेटोनेशन, पिस्टन स्लैप, और बेयरिंग नॉक को अलग करने पर ध्यान केंद्रित है।
Safe listening practices and basic toolsCharacteristics of combustion knock and detonationIdentifying piston slap under varying loadsRecognizing main and rod bearing knockUsing a mechanic’s stethoscope effectivelyCorrelating sound patterns with engine data