Aralin 1Pagputol at paghubog ng tiles: wet saw, angle grinder, nippers at tamang edge finishingTinutukan ng seksyong ito ang ligtas at tumpak na pagputol at paghubog ng tiles. Iihcompare mo ang wet saws, angle grinders, at nippers, matututunan ang edge finishing methods, dust control, at mga teknik para sa malinis na cuts sa paligid ng fixtures, niches, at floor wastes.
Paggamit ng wet saw para sa tuwid at mitre cutsAngle grinder techniques at blade choiceTile nippers para sa maliliit na notches at curvesEdge smoothing, arrising at polishingDust control at personal protective gearAralin 2Aplikasyon ng waterproofing: bilang ng coats, wet film thickness, curing, lap details sa paligid ng joints, penetrations at drainsDito matututunan mo kung paano mag-aplay ng waterproofing membranes sa wet areas, kabilang ang kinakailangang coats, kontrol ng wet film thickness, curing times, at tamang lapping sa mga sulok, joints, penetrations, at drains upang makamit ang continuous, matibay na barrier.
Pagsusuri ng kinakailangang wet film thicknessBilang ng coats at recoat intervalsLap details sa sulok at wall-floor jointsPag-seal sa paligid ng pipes, mixers at drainsCuring conditions at proteksyon mula sa pinsalaAralin 3Pagsusuri at pagsubok: bond tests, hollow-sound detection gamit ang mallet, waterproofing continuity checks at flood testingDito matututunan mo kung paano suriin at subukin ang waterproofing at tile work. Kasama ang bond testing, pag-detect ng hollow-sounding tiles gamit ang mallet, pagsusuri ng membrane continuity sa details, at paggawa ng controlled flood tests sa wet areas.
Biswal na tseke ng membranes at detailsSimple bond at pull-off field testsHollow-sound detection gamit ang rubber malletFlood testing shower bases at floorsPagtatala ng mga depekto at repair proceduresAralin 4Tile layout at set-out: dry layout, symmetry, grout joint width, tile orientation at reference linesDito matututunan mo kung paano magplano ng tile layout sa banyo. Kasama ang dry laying, symmetry, grout joint width, tile orientation, reference lines, centering sa features, at pamamahala ng cuts sa sulok, niches, at drains para sa propesyonal na tapunan.
Pagbasa ng plans at pagsusuri ng banyoPag-establish ng control at reference linesDry layout upang subukin ang pattern at cutsPagpili ng grout joint width at alignmentPag-center ng tiles sa key visual featuresAralin 5Mga tile fixing methods: back-buttering, butter-and-bedding para sa floors, wall adhesive application methods at tamang trowel sizesIpinaliliwanag ng seksyong ito ang tamang tile fixing methods para sa banyo walls at floors. Matututunan mo kung kailan gagamitin ang back-buttering, butter-and-bedding, tamang trowel sizes, coverage targets sa wet areas, at mga teknik upang maiwasan ang voids sa ilalim ng tiles.
Pagpili ng trowel notch size at patternBack-buttering ng malalaki at matitibay na tilesButter-and-bedding para sa floors at fallsPagkamit ng minimum coverage sa wet zonesPag-iwas sa voids at air pockets sa ilalim ng tilesAralin 6Substrate preparation para sa waterproofing: primers, fillets sa wall-floor junctions, surface profile requirementsTinutukan ng seksyong ito ang paghahanda ng mga substrate ng banyo bago ang waterproofing. Susuriin mo ang paglilinis, priming, pagbuo ng fillets sa wall-floor junctions, crack treatment, falls sa drains, at surface profile requirements para sa maaasahang membrane adhesion.
Paglilinis at decontaminasyon ng substratesPagpili at aplikasyon ng angkop na primersPagbuo ng cementitious fillets sa junctionsPagtrato ng bitak, butas at surface defectsPagsusuri ng falls, flatness at surface profileAralin 7Waterproofing strategies: sheet membranes, liquid-applied membranes, cementitious waterproofing — selection criteria at compatibilityIihcompare ng seksyong ito ang sheet, liquid, at cementitious waterproofing systems para sa banyo. Matututunan mo ang performance criteria, substrate compatibility, typical failure modes, at kung paano pumili ng mga sistemang sumusunod sa codes at manufacturer guidance.
Sheet membranes: uri, gamit, limitationsLiquid-applied membranes: key propertiesCementitious coatings para sa wet areasCompatibility sa substrates at primersChemical resistance at service conditionsAralin 8Tile adhesive selection: cement-based thinset, flexible mortars, rapid-set adhesives — selection batay sa substrate at tile typeIpinaliliwanag ng seksyong ito kung paano pumili ng tile adhesives para sa banyo walls at floors. Iihcompare mo ang cement-based thinset, flexible at rapid-set mortars, at isasama sa substrates, tile formats, porcelain density, at inaasahang galaw o kahalumigmigan.
Cement-based thinset classificationsFlexible mortars para sa movement-prone basesRapid-set mortars: gamit at limitationsAdhesive choice para sa porcelain at malalaking tilesAdhesive compatibility sa waterproofingAralin 9Pagsusuri ng moisture-damaged masonry at block walls: paglilinis ng stains, pag-alis ng failed render, at drying strategiesMatututunan mo kung paano suriin ang moisture-damaged masonry at block walls bago ang waterproofing. Kasama ang pag-diagnose ng moisture sources, pag-alis ng failed render, paglilinis ng efflorescence at mold, at controlled drying strategies na maiiwasan ang karagdagang cracking.
Pagkilala ng moisture sources at pathwaysPagsubok ng masonry moisture contentPag-alis ng maluwag na render at contaminated layersPaglilinis ng efflorescence, mold at stainingDrying strategies at re-rendering timingAralin 10Grouting, sealants at movement joints: grout types, joint cleaning, silicone sealants sa perimeter at fixtures, at expansion joint placementMatututunan mo kung paano mag-grout at mag-seal ng tiled bathrooms, kabilang ang grout types, joint cleaning, mixing at packing techniques, silicone sa perimeters at fixtures, at pagdidisenyo ng movement at expansion joints upang kontrolin ang cracking at leaks.
Pagpili ng cementitious at epoxy groutsJoint cleaning at preparation bago ang groutingTamang grout mixing at aplikasyonSilicone sa perimeters, sulok at fixturesMovement at expansion joint placement