Lección 1Verificaciones ensamblaje final: auditoría torque, inspección ángulos línea transmisión y juego juntas, holgura escape y envoltura calor si necesarioEsta sección se enfoca en verificación final de ensamblaje, incluyendo auditoría torque de sujetadores críticos, verificaciones ángulos línea transmisión, inspección juego juntas universales y confirmación holgura escape y protección calor alrededor nuevo diseño transmisión.
Structured torque audit checklistDriveline angle measurement methodsU‑joint play and phasing inspectionExhaust clearance and rattle checksHeat wrap and shield installationLección 2Instalación selector y configuración enlace: remoción consola, montaje selector, ajuste cable, alineación detent y lubricación bujesEsta sección explica cómo instalar el selector y configurar enlace o cables, incluyendo remoción consola, montaje base selector, alineación enlace, ajuste cable, verificación detent y lubricación pivotes y bujes para tacto preciso.
Console and trim disassembly stepsShifter base alignment and fasteningRod or cable linkage orientationDetent position and gate verificationBushing and pivot lubrication pointsLección 3Ajuste y montaje transmisión: verificaciones acoplamiento eje entrada, instalación piloto/rodamiento, torque cruce y montajeEsta sección cubre posicionar y montar correctamente la transmisión manual, verificando acoplamiento eje entrada, instalando o inspeccionando rodamiento piloto y aplicando torque a cruce y hardware soporte para mantener alineación y confiabilidad.
Verifying bellhousing to block alignmentInput shaft engagement and endplay checkPilot bearing selection and installationCrossmember positioning and shim choicesMount torque specs and fastener sequenceLección 4Adaptaciones cableado ECU/TCU: ajuste interruptor neutral/seguridad, cableado lámpara reversa, verificaciones señales velocímetro/tacómetro, estrategias reprogramación/inmovilizador TCMAquí configurarás cableado y módulos control para setup manual, incluyendo circuitos seguridad neutral y lámpara reversa, señales velocímetro y tacómetro, y estrategias para inmovilizador, ECU y codificación TCM o eliminación según requerido.
Neutral safety and clutch switch wiringReverse lamp switch integrationSpeedometer and tachometer signal pathsECU coding for manual configurationTCM removal or reprogramming optionsLección 5Fluidos, sangrado y ajustes: procedimientos llenado caja, sangrado sistema hidráulico, ajuste holgura libre embrague, configuración tacto cambioAprenderás selección correcta fluidos y procedimientos llenado para caja manual, sangrado adecuado sistemas hidráulicos embrague, ajuste holgura libre embrague y afinación tacto cambio para balancear acoplamiento suave con selección engranajes confiable.
Selecting gearbox oil type and gradeFill level checks and leak inspectionHydraulic clutch bleeding techniquesClutch freeplay and bite point setupTest drive and shift feel refinementLección 6Instalación sistema embrague: reemplazo o mecanizado volante, alineación disco embrague, secuencia torque y verificaciones runout rotorEsta sección cubre instalación sistema embrague, incluyendo inspección y mecanizado o reemplazo volante, alineación disco embrague, torque secuencia plato presión y verificaciones runout para prevenir vibración y desgaste prematuro.
Flywheel inspection and resurfacingChoosing bolts and thread treatmentClutch disc alignment tool usePressure plate torque patternRunout measurement and limitsLección 7Recepción vehículo y documentación: fotos, VIN, registro codificación módulos, lista prueba manejo pre-conversiónAquí aprenderás a recibir el vehículo, documentar su condición, capturar fotos, registrar VIN y datos módulos, y realizar prueba manejo pre-conversión estructurada para establecer bases de manejabilidad, ruido y códigos falla.
Initial walkaround and photo setRecording VIN, mileage, and optionsScanning and saving module coding dataPre‑conversion road test checklistCustomer concerns and sign‑off formsLección 8Secuencia remoción: drenaje fluidos, desconexión batería, remoción transmisión automática, remoción convertidor torque/flexplate, remoción escape y cruceEsta sección explica orden lógico seguro para drenar fluidos, desconectar batería, remover transmisión automática y convertidor torque, manejar flexplate y desmontar componentes escape y cruce sin daños.
Battery disconnect and safety prepDraining ATF and related fluidsSeparating torque converter from flexplateSupporting and lowering the transmissionExhaust and crossmember removal stepsLección 9Ajuste caja pedales y configuración actuación embrague: instalando cilindro maestro o cable, enrutamiento líneas hidráulicas o cable, colocación depósito y fijaciónAprenderás a ajustar caja pedales y configurar actuación embrague, incluyendo instalación cilindro maestro o cable, consideraciones relación pedal, enrutamiento líneas hidráulicas o cable, colocando depósito y asegurando componentes contra roce y flexión.
Pedal box removal and trial fittingMaster cylinder or cable bracketryHydraulic line or cable routing pathsReservoir placement and mountingPedal travel, stop, and switch adjustmentLección 10Modificaciones firewall/túnel y montaje: midiendo holguras requeridas, corte/parcheo, agregando refuerzos y escudo calor si necesarioAquí aprenderás a evaluar y modificar firewall y túnel para holgura caja manual, incluyendo medición, corte, parcheo, refuerzo y agregado escudo calor preservando integridad estructural y sellado interior.
Measuring gearbox and shifter envelopeMarking and cutting the tunnel safelyFabricating and welding patch panelsAdding structural reinforcementsSeam sealing, paint, and insulation