Lesson 1Process selection rationale for root, hot, and fill passes on 6 mm 304L butt joint (e.g., GTAW root + pulsed GMAW fill)Gives a clear plan for choosing ways for root, hot, fill passes on 6 mm 304L butt joins, matching GTAW, regular GMAW, pulsed GMAW on reach, output, bend, code or buyer needs.
Evaluating joint access and position limitsGTAW roots for control and low defect ratesPulsed GMAW for fill and cap productivityBalancing heat input and distortion controlExample procedures for 6 mm butt jointsLesson 2Shielding gas selection and flow rates: pure argon, argon-helium blends, and backing gas needsCovers shield and back gas picks for GTAW and GMAW on 304L, pure argon, argon-helium mixes, nitrogen-free back gases, with suggested flow rates, nozzle sizes, tricks to stop holes and rusting.
Pure argon for GTAW and GMAW on 304LArgon–helium blends for higher heat inputBacking gas types and oxygen limitsTypical flow rates and nozzle selectionPreventing porosity and sugaring issuesLesson 3Wire and electrode diameters and feed settings for root and fill passes (typical sizes for 6 mm thickness)Sets common wire, electrode sizes for 6 mm 304L roots, fills, tying to feed speed, amps, deposit rate, tuning for deep reach, bead shape, position welding needs.
Typical GTAW tungsten diameters for 6 mmSolid wire diameters for GMAW on 304LSMAW electrode sizes for plate and pipeWire feed speed versus amperage relationAdjusting size and feed for position weldingLesson 4Recommended parameter ranges: current type, amperage ranges for 6 mm, voltage, travel speed approximationsSets real current, voltage, travel speed ranges for GTAW, GMAW, SMAW on 6 mm 304L plate, balancing reach, bead shape, bend control, dodging no-fusion or burn-through.
Current type and polarity choice by processTypical amperage ranges for 6 mm plateVoltage windows for short, spray, and pulseTravel speed targets for root and fill passesAdjusting parameters for position and fit-upLesson 5SMAW (stick) and pulsed TIG/GMAW when applicable: electrode choices and use-casesTells when SMAW, pulsed GTAW, pulsed GMAW suit 304L, field jobs, odd positions, thin-thick shifts, guiding electrode types, sizes, working ranges.
SMAW electrodes for 304L stainless jointsPulsed GTAW for thin or heat‑sensitive areasPulsed GMAW for out‑of‑position weldsElectrode and wire diameter selectionTypical parameter windows for each optionLesson 6GTAW (TIG) fundamentals: AC vs DC, electrode types (thoriated/lanthanated), electrode preparation and sharpeningReviews GTAW basics for stainless, matching AC DC use, tungsten types, tip prep ways, showing electrode shape, current type, shield gas mix for arc focus, reach, bead finish.
When to use DCEN versus AC on stainlessThoriated versus lanthanated tungsten typesGrinding and tapering tungsten electrodesAvoiding contamination and arc wanderCurrent limits by tungsten size and tip formLesson 7Joint position and rotator use for circumferential welds on ~1 m diameter shellsCovers joint placing, rotator use for round welds on about 1 m shell diameters, setup, line-up, speed check, safety, steady heat put-in, bead shape round the circle.
Setting up shells on rollers or rotatorsAligning joint gaps and high‑low mismatchSynchronizing rotation and travel speedCable management and operator safetyMaintaining consistent bead profileLesson 8GMAW (MIG/MAG) fundamentals: transfer modes (short-circuit, globular, spray, pulsed), equipment setupStarts GMAW basics for stainless, short-circuit, globular, spray, pulsed moves, setting power source, feeder, gun, coil for steady arcs, low splatter on 304L joins.
Short‑circuit transfer on thin or root passesGlobular transfer limits and drawbacksSpray transfer for flat and horizontal weldsPulsed spray for positional stainless workKey GMAW equipment setup parametersLesson 9Filler metal classifications for 304L stainless: ER308L/ER309L/ER316L selection rules and wire/electrode diametersExplains AWS filler types for 304L stainless, matching ER308L, ER309L, ER316L, picking wire electrode sizes for join plan, position, strength, rust needs.
Overview of AWS stainless filler designationsWhen to select ER308L for 304L base metalUsing ER309L for dissimilar or butteringUsing ER316L for enhanced corrosion serviceDiameter selection for root and fill passesLesson 10Polarity and power source considerations for GTAW and GMAW with stainlessDetails power source type, pole effects on arc steady, reach, bead shape in GTAW GMAW on stainless, steady current vs steady voltage, right terminal links.
CC versus CV power source characteristicsGTAW polarity and terminal connectionsGMAW polarity for solid and metal‑cored wireEffects of polarity on penetration patternTroubleshooting arc instability issuesLesson 11Equipment accessories: gas lenses, purging systems, trailing shields, backing strips, and heat sinksExplains add-ons like gas lenses, purge setups, trailing shields, back strips, heat sinks better shield, cut bend, guard root good in 6 mm 304L plate, shell joins.
Gas lenses for laminar shielding coverageInternal purging dams and purge monitorsTrailing shields for long stainless beadsBacking bars, strips, and ceramic tilesHeat sinks for distortion and burn‑through
