Lesson 1Tapes, beads, and reinforcement: paper tape vs fiberglass mesh, metal and vinyl corner beads, flexible trim for revealsThis covers tapes, beads, and strength items that guard joints and edges. Compare paper and fiber tape, pick metal or plastic beads, and use bendy trims to make clean shows and strong edges that do not crack easily.
Paper tape vs fiber mesh strengthInner and outer edge bead picksMetal vs plastic beads and rust problemsBendy trims for shows and curvesNailing and setting edge beadsLesson 2Large tools and equipment list: drywall lifts, screw guns, screw setters, taping knives (6", 10", 12", 14"), hawk and trowel, mud pan, mixing drill and paddle, pole sanderThis lists big tools that help work faster and better in drywall. Learn right use of lifts, screw tools, taping knives, holders, pans, mixers, and long sanders, plus setup, fixes, and safe holding ways.
Drywall lift setup and safe useScrew tools, group drivers, and settersTaping knife sizes and right waysUsing holder, mud pan, and spreader wellMixing drill, paddle, and long sander useLesson 3Personal protective equipment and site safety gear: NIOSH-rated respirators for dust, eye protection, hearing protection, gloves, hard hat, knee padsThis outlines body safety gear and site tools for drywall tasks. Pick approved breathers, eye and ear guards, hand covers, head hats, and knee guards, and set up safe paths and clean areas for work.
Approved breathers and filter picksEye and face guards for dust and bitsEar guards for loud toolsHand covers, head hats, and safe shoesKnee guards and body-friendly work waysLesson 4Joint compounds and additives: setting-type compounds (hot mud), ready-mix all-purpose and topping compounds, primers and bond coat optionsThis looks at joint pastes and adds for taping, filling, and ending. Compare set-type and ready pastes, pick all-use or top mud, and use base paints and stick coats to make better hold and last longer.
Set-type pastes and work timesReady all-use vs top mudLight vs normal paste useAdds for easy work and less shrinkBase paints and stick coats on hard spotsLesson 5Fasteners, adhesives, and backing: drywall screws (coarse/fine thread), drywall nails, construction adhesive, backing clips for ceiling jointsThis checks nails, glues, and support systems that hold drywall. Compare screw twists, nails, and build glues, and use support clips and blocks to hold joints, edges, and roof joins strong.
Rough vs fine twist drywall screwsDrywall nails and when not to useBuild glue use and spacesSupport clips for weak jointsBlocks for lights and heavy loadsLesson 6Consumables and sundries: screws, washers, caulk, mesh patches for repair, masking tape, drop clothsThis reviews used items and small things that help drywall fitting and fixes. Pick screws, rings, seal paste, mesh fixes, cover tape, and floor sheets, and plan amounts to cut waste and keep site running smooth.
Drywall screws, rings, and spacesSeal types for gaps and move jointsMesh fixes for small holesCover tape and surface guardsFloor sheets and dust trap choicesLesson 7Accessory tools and clean-up equipment: utility knives, T-squares, chalk line, laser level or plumb bob, ladders and scaffolding, HEPA vacuum and negative air machine (if available)This describes extra tools and clean gear that make work exact and safe. Use knives, mark tools, steps, frames, clean suckers, and air pull machines to keep areas clean, right, and follow rules.
Work knives, blades, and safe holdT-squares, chalk lines, and mark checksLaser levels and drop lines for line-upStep and frame setup and checksClean suckers and air pull machinesLesson 8Finishing materials: sanding screens, joint compound mixing tools, surface primers (PVA and drywall primer) and block fillersThis focuses on end materials that ready surfaces for paint or rough. Pick sand roughs, use mix tools right, and choose PVA base paints, drywall bases, and block fillers for different bases to make smooth.
Sand screens vs paper picksHand and long sand waysJoint paste mix tools and carePVA and drywall base usesBlock fillers for holey or hurt wallsLesson 9Drywall board types and sizes: gypsum regular, moisture-resistant (green/blue board), fire-rated (Type X), typical thicknesses (1/2", 5/8") and recommended choices for walls and ceilingsThis explains common drywall board kinds, inside strength, and usual sizes. Match normal, water-proof, and fire boards to places, and pick right thicks for walls, roofs, and special needs or rules.
Normal gypsum board strength and usesWater-proof boards for wet spotsFire Type X and rule needsUsual thicks and edge shapesBoard picks for walls vs roofs
