Lesson 1Interiors and Finishes: Partition Types, Gypsum Systems, Floor Finishes, Acoustic and Fire-Rated AssembliesThis part teaches how to set inside and finish areas, like walls, gypsum setups, floor covers, and sound and fire-safe parts, making clear overlaps between wall, floor, and special ceiling works.
Wall Frames, Plans, and Support AreasGypsum Board Fixing, Joining, and Finish LevelFloor Cover Types, Prep, and Change DetailsSound Ceilings, Blocks, and Noise FixesFire-Safe Walls, Shafts, and Hole DetailsLesson 2Special Trades and Ancillary Scope: Elevators, Site Paving, Landscaping, Temporary Works, Testing and CommissioningThis part sets areas for special works and extra jobs, like lifts, site roads, plants, temp works, and testing starting, making clear duties, links, and how well they work.
Lift Shafts, Pits, and MatchingSite Roads, Edges, and Joint DutiesPlants, Growing, and Water AreasTemp Works, Scaffolds, and GuardsTesting, Starting, and Handover RulesLesson 3Roofing and Terraces: Low-Slope Roofing Assemblies, Insulation, Drainage, Roof Access and Fall-ProtectionThis part covers roof and terrace areas, like flat roof setups, warm layers, water flow, and access systems, setting trade ends between frame, roof, metal sheets, safety, and water-proof workers.
Flat Roof Cover and LayersRoof Warm Layer Type, Thick, and SlopeRoof Water Drains, Holes, and Extra PathsWall Tops, Covers, and EndsRoof Access Steps, Doors, and HoldsLesson 4Envelope and Façade Systems: Curtain Wall vs Masonry Veneer vs Storefront, Air/Vapor Barriers, Flashing and InterfacesThis part covers outside cover and face areas, comparing glass walls, stone covers, and shop fronts, and making clear air and wet barriers, covers, and link duties at all changes.
Glass Wall Design, Supply, and FittingStone Cover Support, Ties, and DrainsShop Front Frames, Glass, and PartsAir and Wet Barrier Full AreaCovers, Ends, and Link DetailsLesson 5Primary Structure: Concrete Casting Sequence, Rebar Placement, Formwork, Steel Erection and Connections, Composite SystemsThis part details how to split main frame work into clear areas, like concrete, steel bars, forms, and steel build, while setting links, allowed gaps, and build order between trades.
Concrete Pour Order by Level and BreaksSteel Bar Supply, Drawings, and Site PlaceForm Design, Remove, and Support AreaSteel Make, Build, and Bolt JobsMixed Deck, Pins, and Concrete Top AreaLesson 6Foundations and Below-Grade: Piling vs Spread Footings, Mat Foundations, Waterproofing, Sub-Slab Drainage and InsulationThis part covers how to set and match base and under-ground work, like piles, spread and flat bases, water-proof, drain, and warm layers, with clear ends between frame, ground, and water-proof trades.
Piles vs Spread Base DutiesFlat Base Steel and PlaceUnder-ground Wall and Floor Water-Proof AreaUnder-Floor Drain, Pits, and Link-InsUnder-Ground Warm Layers and Guard BoardsLesson 7Sitework: Utilities, Demolition, Shoring, Excavation, Dewatering, Erosion and Sediment ControlsThis part teaches how to set site work, like services, break down, support, dig, dry water, and soil loss controls, with clear pass-overs between ground, frame, and building trades and needed order.
Choose Break Down and Save AreaDig, Fill Back, and Pack LimitsTemp and Last Support SystemsDry Water Ways, Out Flow, and WatchUnder Ground Services Paths and LinksLesson 8MEP Scope: HVAC Systems Selection and Zoning, Plumbing Risers and Sanitary Drainage, Electrical Distribution, Fire Protection and Life-Safety SystemsThis part details how to set service areas, like air heat choice and zones, water pipes and waste drain, power spread, and fire guard, while matching supports, holes, and safe life links.
Air Heat Tools, Zones, and Pipe AreaWater Heat, Cold, and Condense PipeWater Pipe Rises, Stacks, and Air Out PathsPower Spread, Boards, and FeedsFire Water Sprays, Alarms, and Safe Life Ties
