Lesson 1Venting, combustion air and condensate handling: atmospheric vs power venting, direct-vent vs B-vent, condensate trap and drain for condensing unitsDis lesson explain venting options for gas water heaters, including atmospheric and power vent systems, direct-vent and B-vent configurations, and correct condensate trapping, neutralizing, and draining for high-efficiency condensing units.
Atmospheric versus power vent conceptsDirect-vent and B-vent configurationSizing and routing vent pipingProviding adequate combustion airCondensate trap and drain installationLesson 2Commissioning steps: filling and purging air, leak tests (water and gas), setting thermostats and temperature verification, TPR valve functional test, combustion analysis basics for gas unitsDis lesson detail the full commissioning sequence, including filling and purging air, water and gas leak testing, thermostat setup, temperature verification, TPR valve functional checks, and basic combustion analysis steps for gas-fired water heaters.
Filling system and purging trapped airWater and gas leak testing proceduresSetting thermostats and limit controlsVerifying outlet temperature and mixingTPR valve functional test procedureBasic combustion analysis for gas unitsLesson 3Valves and safety device installation: isolation valves, union/flare provisions, TPR valve orientation and discharge piping, expansion tanks and check valvesDis lesson cover correct selection and placement of isolation valves, unions, TPR valves, expansion tanks, and check valves, focusing on orientation, support, discharge routing, and code-compliant protection against overpressure and backflow in hot water systems.
Locating cold and hot isolation valvesInstalling unions and flare connectionsTPR valve orientation and discharge routingExpansion tank sizing and placementCheck valve selection and backflow controlLesson 4Gas connection basics for plumbers: union, shutoff valve placement, leak testing methods (soapy solution, gas detector), and coordinating with gas supplier/licensed installersDis lesson introduce plumbers to safe gas connection practices, covering unions, shutoff valve placement, approved leak testing methods, documentation, and coordination wid gas suppliers or licensed gas fitters where regulations require.
Locating appliance shutoff valvesInstalling unions for service accessSoapy solution leak testing methodUsing electronic gas leak detectorsCoordinating with gas supplier or fitterLesson 5Electrical interface and coordination: disconnects, dedicated circuit needs, verifying electrician work, and verifying bonding/groundingDis lesson cover electrical interface requirements for water heaters, including disconnects, dedicated circuits, verifying electrician work, checking bonding and grounding, and confirming dat controls and safety devices receive correct power.
Identifying required circuit capacityLocating and labeling disconnectsVerifying electrician rough-in workChecking bonding and grounding pathsConfirming control and sensor powerLesson 6Pre-installation preparation: permits, site checks, service isolation sequence, and required tools/materials checklistDis lesson outline pre-installation tasks such as confirming permits, reviewing site conditions, verifying clearances, planning service isolation, and assembling a complete tools and materials checklist to avoid delays and safety issues.
Confirming permits and documentationAssessing site access and clearancesVerifying water, gas and power availabilityPlanning safe service isolation sequenceTools and materials checklist preparationLesson 7Cold/hot plumbing work: pipe material choices (copper, PEX, CSST considerations), basic sizing tables, branching to two bathrooms, kitchen, laundry, and recirculation optionsDis lesson explore hot and cold plumbing layout for water heaters, including pipe material choices, basic sizing references, routing to bathrooms, kitchen and laundry, and options for recirculation loops to improve hot water delivery times.
Selecting copper, PEX or other materialsUsing basic pipe sizing tables safelyBranching to bathrooms and kitchen loadsSupplying laundry and auxiliary fixturesDesigning simple recirculation loopsLesson 8Documentation and handover: labeling, as-built notes, safety stickers, and owner-operational guidance sheetDis lesson explain how to prepare clear, compliant documentation at completion, including accurate as-built notes, durable labels, safety and warning stickers, and a practical owner operation and maintenance guide to support safe long-term system use.
Creating clear as-built system schematicsLabeling valves, circuits and isolation pointsApplying safety, warning and hazard stickersPreparing owner operation and maintenance sheetRecording serial numbers and warranty dataLesson 9Safe removal of an old gas storage heater: depressurizing gas, draining tank, disconnecting utilities, handling and disposal of corroded equipmentDis lesson describe safe procedures for decommissioning and removing an old gas storage heater, including depressurizing gas, draining the tank, disconnecting utilities, managing corrosion, and arranging compliant transport and disposal.
Shutting down and isolating the heaterDepressurizing and capping gas linesDraining and flushing the storage tankDisconnecting water and electrical feedsHandling corroded or damaged componentsTransport and disposal requirements
