Lesson 1Ground and base check: crane bottom, pad condition, temp road, surface bear power and ground water/drain problemHere you go learn how to check crane base, pad, and access road, make sure bear power match load, find soft place, hole, or wash away, and check drain or ground water dat could make steady weak during work.
Look at ground tech and bear dataCheck crane base, anchor, and padLook at temp road and access wayFind soft ground, hole, and wash awayCheck drain and ground water effectWrite and report ground problemLesson 2Talk equipment check: radio test, battery handle, extra hand radio, sign and backup hand sign ruleYou go learn how to check and test talk tool, include radio, battery, charger, extra unit, and fix sign, and how to set clear backup hand sign rule to keep control if main system fail during lift.
Check radio, headset, and chargerTest radio reach and sound clearHandle battery and extra hand unitMake sure post crane and site signSet standard hand and arm signPlan talk fail backupLesson 3Weather check way: wind watch, gust guess, see check, rain/ice effect and when to stop lift workDis part tell how to watch wind speed and way, read gust guess, check see, rain, snow, and ice, and use maker and rule limit to decide when to hold or stop crane work for weather safe.
Use wind meter and wind showLook at weather guess and gust trendCheck see, fog, and night lightLook at rain, snow, and ice hitUse wind and weather work limitWay to stop and start lift againLesson 4Wire rope, lift rope and hook: check rule, wear limit, oil and end-life signYou go learn check rule for wire rope, lift rope, and hook, include look for break wire, rust, bend, shape change, throat open, latch work, oil good, and know end-life condition dat need take out service.
Find break wire and strand hurtCheck rope thick and stretchFind rust, bend, and bird cageCheck hook for crack and shape changeMake sure hook latch there and workOil way and throw away ruleLesson 5Tower crane build check: mast, turn ring, jib, counter weight, rust and shape change showDis part cover look and work check of tower crane build, include mast part, tie, turn ring, jib, counter jib, and counter weight, look for crack, loose fix, rust, shape change, and strange noise or move.
Check mast part and joinCheck tie, anchor, and brace systemLook at turn ring and bolt tightCheck jib, counter jib, and hangMake sure counter weight condition and sitFind rust, crack, and bendLesson 6Work area look: find overhead power line, next build, public street danger, people walk way and no go zoneHere you go learn to look crane work area for overhead power line, near build, traffic way, and public show, den set no go zone, block, and watcher to control people and vehicle move around lift work.
Find and mark overhead power lineLook clear to build and roofCheck danger to street and walk wayPlan load path and swing areaSet up block and no go zoneWork with site guard and trafficLesson 7Load chart read: rate by reach, set limit, move factor and cut rate for add onDis part show how to read and use tower crane load chart, include power by reach and set, effect of jib long and counter weight, move load factor, cut rate for add on, and use chart to plan safe lift work.
Know chart lay and wordPower change with reach and highEffect of jib long and setCount wind and move factorCut rate for hook, block, and slingCheck plan lift with chartLesson 8Crew skill and role check: make sure rigger, signal and operator paper and pre-shift talk listDis part cover make sure operator, rigger, and signal skill, look at need paper, write daily fit for work, and do set pre-shift talk dat line crew on task, danger, and talk.
Make sure operator license and addCheck rigger and signal person skillMake sure health fit and tire statusLook at site need trainDo set pre-shift talkWrite crew check recordLesson 9Safety tool and limit switch: work check for over load, anti-two-block, boom angle/reach, wind speed show and emergency stop systemDis part show how to check safety tool and limit switch, include over load guard, anti-two-block, boom angle and reach show, wind alarm, and emergency stop wire, make sure dem work good before lift start.
Test over load and moment limitMake sure anti-two-block workCheck boom angle and reach showLook at wind speed alarm and cutTest emergency stop button and wireWrite safety tool test result
