Lesson 1Flue gas path and heat recovery: economizers, sootblowers, draft controls, flue inspection issuesLooks at the flue gas path from furnace to stack, with focus on getting back heat, controlling draft, and keeping clean. Talks about how economizers work, using sootblowers, check points, rust risks, and how dirt affects efficiency.
Gas flow path: furnace, passes, breeching, stackEconomizer function, fouling, and leak detectionSootblower types, sequencing, and safe operationDraft fans, dampers, and draft control tuningFlue inspection, corrosion, and leakage issuesLesson 2Feedwater system: deaerator, feedwater tank, make-up water, condensate returnExplains the full feedwater setup from make-up water to steam drum, including deaerators, feed tanks, and condensate coming back. Focuses on removing oxygen, level control, venting, and how the design affects reliability.
Deaerator principles, venting, and pressure controlFeedwater tank layout, heating, and level controlMake-up water sources, metering, and valvesCondensate return lines, traps, and receiversFeedwater regulation valves and control schemesLesson 3Safety devices and controls: safety valves, pressure gauges, level switches, low-water cutoffs, interlocksGoes over key boiler safety gear and control setups, showing how they stop too much pressure, low water, and unsafe starts. Stresses checking, testing times, failure signs, and paperwork needs.
Safety relief valves: sizing, testing, common faultsPressure gauges and pressure switches calibrationLevel controls, probes, and float switch maintenanceLow-water cutoffs: testing, failures, code rulesSafety interlocks and startup permissive logicLesson 4Pumps and piping: feedwater pumps, condensate pumps, seals, couplings, alignment and vibration basicsDetails boiler feedwater and condensate pumping setups, including pump types, NPSH, seals, and couplings. Stresses alignment, vibration basics, oiling, and regular checks that stop cavitation, leaks, and early breakdowns.
Feedwater pump types, curves, and NPSH limitsCondensate pumps and receiver tank operationMechanical seals, packing, and leak controlCouplings, soft foot, and shaft alignment checksVibration symptoms, causes, and field checksLesson 5Boiler pressure vessel and steam drum: construction, materials, common failure modesDescribes the boiler pressure vessel and steam drum, including build methods, materials, and inside parts. Reviews common breakdowns, check methods, and rules for fixes and changes.
Drum and shell construction, heads, and nozzlesMaterials selection, stress, and temperature limitsSteam drum internals: separators and dryersThermal fatigue, corrosion, and cracking modesInspection intervals, NDE methods, and repairsLesson 6Instrumentation and control systems: PID loops, pressure/level transmitters, flame safeguard, alarms and HMI basicsIntroduces boiler instruments and control setup, including transmitters, control loops, and flame safety. Covers PID basics, alarm handling, HMI screens, and how operators read signals for safe actions.
Pressure, level, and temperature transmittersPID loop terms, tuning impact, and stabilityBurner management and flame safeguard logicAlarm priorities, setpoints, and nuisance tripsHMI graphics, trends, and operator interfacesLesson 7Burner and combustion system: types, fuel train components, flame detection, combustion tuning fundamentalsLooks into burner and combustion system parts, fuel trains, and flame spotting. Covers burner types, air-fuel mix control, purge steps, and basic tuning to balance safety, efficiency, and smoke.
Burner designs for gas, oil, and dual-fuel serviceFuel train valves, regulators, and safety shutoffsIgnition systems and flame scanner technologiesAir–fuel ratio control and excess air effectsCombustion tuning steps and field test methodsLesson 8Water treatment equipment: hardness control, deaeration, chemical dosing, blowdown systemsFocuses on water treatment gear that protects the boiler from scale, rust, and carryover. Explains hardness control, deaeration kit, chemical adding, and blowdown setups, linking tests to settings.
Softening and hardness removal equipment basicsOxygen removal: mechanical and chemical methodsChemical dosing pumps, tanks, and injection pointsContinuous and intermittent blowdown hardwareMonitoring water quality and adjusting treatment
