Lesson 1Battery repair process workflow: isolation, safe disassembly, cell verification, balancing, reassembly, and test cycleFollow a step-by-step safe flow for battery fixes. You'll do power cut, open packs careful, check welds and covers, change cells, balance again, seal up, and run tests before giving back scooter.
Isolation, PPE, and workbench preparationOpening packs without causing new damageCell replacement, welding, and insulationFinal balancing, sealing, and test ridesLesson 2Cell-level diagnostics: IR measurement, capacity estimation using simple timed load test, and spotting cell imbalancesGo deep into cell tests. You'll measure inside resistance, guess capacity with time load tests, find uneven cell groups, and pick which cells fit to fix or too risky or costly.
Using ESR meters and four-wire techniquesTimed discharge tests for capacity estimatesFinding weak cells within parallel groupsCriteria for rejecting marginal cellsLesson 3BMS and firmware checks: extracting BMS logs/telemetry where possible, common BMS failure symptoms, and firmware reset/firmware update considerationsLearn to pull and read BMS data if you can. You'll check error logs, ride counts, heat history, firmware versions, and know when reset or update safe or better change hardware.
Connecting to BMS apps, tools, or adaptersReading fault codes, flags, and event logsEvaluating cycle count and SOH indicatorsFirmware reset and update risk assessmentLesson 4Li-ion battery fundamentals: cell chemistry, nominal voltages, capacity (Ah), internal resistance, and state-of-charge estimationGet Li-ion cell makeup, common mixes, and how voltage, capacity, resistance work together. See how dem affect distance, power, aging, and charge level guess in workshop.
Common scooter chemistries: NMC, LFP, NCANominal, max, and cutoff voltage per cellCapacity (Ah) vs. energy (Wh) vs. C-rateInternal resistance and its measurement basicsLesson 5When to replace pack vs. repair cells: economic, safety, and longevity criteria; pros and cons of cell replacement vs. full pack replacementLearn to choose full pack swap or cell fix. Compare cost, safety space, life span, work time, risk so you advise best for rider and your shop.
Cost comparison: parts, labor, and shop overheadRisk assessment: fire, recalls, and liabilityEstimating remaining useful life of old packsWhen to refuse repair and recommend new packLesson 6Interpreting symptoms: sudden shutdown at 40–50% and reduced range — common failure modes (capacity loss, increased internal resistance, BMS cutoff, cell group failure)Match real signs to battery faults. Analyze sudden stops, short range, weak go, shaky gauge to tell capacity drop, high resistance, BMS cut, cell group fail.
Patterns of range loss and voltage sagSudden cutoff at mid SOC and BMS triggersDiagnosing weak cell groups in series stringsDifferentiating pack vs. controller issuesLesson 7Battery management system (BMS) role: balancing, over/under-voltage protection, current limiting, and telemetry interfacesSee how BMS guards pack and rider. Study balance ways, high/low voltage cuts, current limits, heat sense, and data links to controllers or tools.
Passive vs. active cell balancing methodsOver/under-voltage and current protectionsTemperature sensing and thermal deratingBMS data lines: CAN, UART, and proprietaryLesson 8Preliminary non-invasive checks: open-circuit voltage, resting voltage distribution, and pack voltage vs. expected valuesDo quick no-cut tests before opening. Measure open voltage, match specs, check rest drift, decide deep check or straight swap.
Measuring pack open-circuit voltage safelyComparing measured voltage to nameplate dataMonitoring resting voltage over several hoursRed flags that justify deeper investigationLesson 9Under-load and charging checks: voltage sag under load, charge acceptance, charger output verification, and charge port/connector inspectionTest battery safe under ride load and charge. Measure voltage drop, check charger power, charge take, inspect ports for heat, rust, damage.
Simulating real-world load with test equipmentMeasuring and interpreting voltage sagVerifying charger voltage and current outputInspecting charge ports, pins, and wiringLesson 10Battery safety and customer communication: explaining thermal runaway risk, storage/charging guidance, safe transport, and warranty/legal disclaimersBuild safe habits and clear talk with customers. Explain heat run risks, store/charge rules, carry careful, note disclaimers, waivers, warranty limits.
Recognizing and handling high-risk batteriesSafe charging, storage, and transport guidanceCustomer education scripts and checklistsDocumenting waivers and repair limitations
