Lesson 1See Line of Sight and Team Jobs: Main Pilot, See Watcher, Watcher, Data Handler, Client TalkerSet teams to keep see line of sight and safe work. You will set jobs for main pilot, see watchers, and data staff, set talk ways, and match with clients on-site duties.
Law Basics of See Line of SightSet Main Pilot Power and DutiesUse See Watchers and SpottersData Handler and Load Worker TasksClient Talker and On-Site TellsLesson 2Picking Cameras and Sensors for Building Watch: RGB, Wide View, Down vs Side, Video Types, Clearness and Light RangePick cameras and sensors fit to building watch. You will compare RGB choices, focus lengths, down and side views, types, clearness, and light range to help progress track and report.
Pick RGB Cameras for Site WatchWide View vs Longer Focus LengthsDown vs Side Take WaysVideo Types, Bit Rates, and File SizesClearness, Bit Deep, and Light RangeLesson 3Drone Plane Pick: Fixed Wing vs Multi Rotor Trade-Offs, Load Powers, Last Time, and Paper StateCompare drone planes and match to task needs. You will weigh fixed wing and multi rotor trade-offs in last time, load, start needs, and paper, then pick frames that meet law and client wants.
Fixed Wing vs Multi Rotor PowersLoad Power and Turn FitLast Time and Cover Rate ComparesStart, Get Back, and Site LimitsPaper, Okays, and WritesLesson 4Flight Work Plan: Speed, Last Time, Battery Counts, Guess Flight Time Per Battery, Heat Effects on WorkPlan flight work to stop surprises in air. You will guess speed, last time, and flight time per battery, count for load and weather, and plan keeps to keep work safe and guess.
Guess Cruise Speed and Ground SpeedCount Last Time with Load WeightGuess Flight Time Per Battery PackPlan Fuel and Battery Safety KeepsHeat and Wind Effects on WorkLesson 5Flight Way Design: Mapping Grid (Ortho Map), Line Hall Checks, Circle/Pano Shots, Way Point MovieLook flight ways for mapping, check, and movie work. You will design grids, halls, circles, and way paths that follow airspace, cut risk, and give use pictures for work or clients.
Design Ortho Map Grid WaysPlan Line Hall Check FlightsCircle and Pano Shot Design and SafetyWay Paths for Repeat MovieHandle Turns, Wind, and Ground SpeedLesson 6Height, Over Lap, and GSD Plan for Picture Measure: Count GSD, Front/Side Over Lap, and Task HeightLearn how height, over lap, and ground sample distance work in mapping tasks. You will count GSD, set front and side over lap, and pick task height to balance cover, detail, and flight time.
Link Sensor Size, Focus Length, and GSDCount Task Height from Goal GSDPick Front and Side Over Lap PartsChange Over Lap for Land and BuildsBalance GSD, Cover, and Flight TimeLesson 7Tele Measure, Write, and On Board Sets: Write Often, Camera Sets, Shut Speed, ND Filters, and Anti Shake MountMaster tele measure, write, and on board set for sure data. You will set write often, tune camera show, pick ND filters, and cut shake to safe hardware and sure high good pictures and records.
Set Flight Control Write SetsPick Camera Ways and Show ValuesSet Shut Speed for Move ControlPick and Size ND FiltersAnti Shake Mount and Balance ChecksLesson 8Task Split: Number of Goes, Battery Change Moves, Hot/Cold Swap StepsBreak hard jobs into safe, handle goes. You will pick go counts, plan battery swaps, set hot or cold changes, and match ground team tasks to cut down time and risk.
Split Tasks into Logic GoesGuess Goes from Area and GSDPlan Battery Stage and TurnHot Swap vs Cold Swap StepsTeam Jobs During Battery ChangesLesson 9Take Off/Land Place Setup and Ground Control: Mark Pads, Clear Blocks, Control Public Get InUnderstand how to pick and ready safe take off and land places. You will mark pads, clear dangers, handle public get in, and mix ground control points to help true mapping and repeat tasks.
Pick Safe Start and Get Back PlacesMark Pads and Turn to WindClear Blocks and Bits from PlaceControl Public and Vehicle Get InPut and Check Ground Control Points
