Lesson 1Die and calibration tooling: die types for pipes and profiles, mandrels, vacuum sizing, land length and swell controlLooks at die and calibration tooling for pipes, profiles, and sheets. Talks about flow distribution, mandrels, land length, swell control, and vacuum sizing, showing how tooling design affects dimensions and surface finish.
Pipe, profile, and sheet die typesFlow distribution and manifoldsMandrels, pins, and spider supportsDie land length and swell controlVacuum sizing plates and sleevesLesson 2Haul-off and downstream: belt pullers, caterpillar haul-off, speed synchronization with extruderGoes over haul-off and downstream pulling equipment, like belt and caterpillar units. Explains traction control, nip pressure, and matching speed with the extruder to keep product dimensions and surface quality good.
Belt pullers vs caterpillar haul-offSpeed synchronization with extruderNip pressure and slip preventionEffect on wall thickness and ovalityIntegration with downstream cuttersLesson 3Cooling and sizing equipment: water cooling baths, spray rings, cooling tanks, calibrators, vacuum sizing systemsLooks into cooling and sizing equipment after the die, such as water baths, spray cooling, and vacuum calibrators. Discusses heat removal rates, dimension control, internal stresses, and how cooling affects warpage.
Water baths and spray ring designCooling tanks and residence timeCalibrators for profiles and sheetsVacuum sizing for pipes and profilesCooling rate, stress, and warpageLesson 4Screw geometry and selection: screw diameter ranges, L/D ratio, flights, compression and metering zonesExplains screw geometry elements and how they affect melting, mixing, and pressure build-up. Covers diameter, L/D ratio, flight design, compression and metering zones, and tips for picking screws for different polymers and outputs.
Screw diameter and L/D ratio effectsFeed, transition, and metering zonesFlight depth, pitch, and channel volumeBarrier and mixing section optionsScrew selection for materials and outputLesson 5Instrumentation and gauges: melt pressure transducers, die pressure, barrel temperature sensors, flow meters, infrared profile measurementCovers main extrusion instruments, like melt and die pressure, barrel temperature sensing, and flow measurement. Stresses sensor placement, calibration, reading data, and how signals work with alarms, interlocks, and control systems.
Melt and die pressure transducersBarrel temperature sensors and placementFlow meters and mass flow monitoringInfrared profile and surface temperatureCalibration, drift, and signal filteringLesson 6Hopper and material handling: dryers, feeders, gravimetric vs volumetric dosing, contamination controlFocuses on hopper design and handling materials, including drying, conveying, and dosing. Compares gravimetric and volumetric systems, stresses moisture and contamination control, and shares best ways to avoid bridging and segregation.
Hopper design, liners, and bridgingDryers and moisture specification limitsPneumatic and mechanical conveyingGravimetric vs volumetric dosingContamination and metal detectionLesson 7Additive and color feeding systems: side feeders, loss-in-weight feeders, masterbatch feeders, pigment dispersion basicsLooks at feeding systems for additives and colours, comparing volumetric and gravimetric types. Covers side feeding to twin-screws, masterbatch dosing, pigment dispersion quality, and ways to avoid segregation and colour streaks.
Volumetric vs loss-in-weight feedersSide feeders for fillers and regrindMasterbatch feeders and color dosingPigment dispersion and streak controlRefill systems and material segregationLesson 8Types of extruders: single-screw vs twin-screw — principles, advantages, typical applicationsCompares single-screw and twin-screw extruders, explaining how they work, melting and mixing, and how design affects throughput, energy use, and suitability for compounding, recycling, profiles or films.
Single-screw operating principle and meltingTwin-screw co-rotating vs counter-rotatingDistributive and dispersive mixing behaviorTypical applications and material suitabilityEnergy efficiency and throughput comparisonLesson 9Cutting and finishing: flying saws, cold cutters, trimming units for profilesDescribes cutting and finishing for extruded products, like flying saws and cold cutters. Explains syncing with line speed, controlling burrs and dust, dimension accuracy, and trimming profiles to specs.
Flying saws for continuous profilesCold cutters for pipes and tubesCut length control and tolerancesBurr, dust, and chip managementEnd finishing and chamfer optionsLesson 10Extruder main components: barrel zones, feed throat, screw, gearbox, heaters, thermocouples, melt pumpIdentifies main mechanical and thermal parts of an extruder. Explains barrel zones, feed throat, screw, gearbox, heaters, thermocouples, and melt pump, and how design and upkeep affect stability and output.
Barrel zones and cooling circuitsFeed throat design and ventingGearbox, motor, and torque limitsHeaters, thermocouples, and controlMelt pump function and pressure build
