Drywall Partitioning Course

Lesson 1 • Reading Partition Construction Drawings

Teaches interpretation of floor plans, sections, and detail drawings for partition works. Accurate drawing reading is prerequisite to all subsequent installation tasks.

Lesson 2 • Classification of Partition Systems

Surveys major partition categories including fixed, demountable, and movable systems. Provides a framework for selecting system types based on project requirements.

Lesson 3 • Key Industry Terminology

Introduces standardised vocabulary used in partition construction drawings and specifications. Accurate terminology enables effective communication with designers and contractors.

Lesson 1 • Steel Framing Components

Covers light-gauge steel studs, tracks, and accessories used in partition framing. Understanding component profiles and gauges enables correct structural selection.

Lesson 2 • Adhesives, Sealants, and Fasteners

Details mechanical fasteners, construction adhesives, and sealants used in partition assembly. Correct product selection ensures structural integrity and airtight performance.

Lesson 3 • Specialty Partition Materials

Surveys glass, aluminium, cement board, and composite panel materials for specialty partitions. Expands material knowledge beyond standard drywall assemblies.

Lesson 4 • Insulation and Acoustic Materials

Introduces batt, rigid, and spray insulation products used within partition cavities. Material choice determines thermal and acoustic performance of the finished assembly.

Lesson 1 • Hand Tools for Partition Work

Identifies and demonstrates correct use of hand tools essential to partition installation. Proper tool selection reduces rework and improves finish quality.

Lesson 2 • Site Hazard Identification and Control

Teaches hazard identification methods and hierarchy-of-controls application on partition sites. Proactive hazard management prevents incidents before work begins.

Lesson 3 • Personal Protective Equipment

Specifies PPE requirements for dust, noise, eye, and fall hazards in partition work. Consistent PPE use is the primary defence against common site injuries.

Lesson 1 • Establishing Control Lines and Datums

Explains how to establish horizontal and vertical control lines from structural benchmarks. Control lines govern all subsequent partition positioning and alignment.

Lesson 2 • Setting Out Partition Positions

Demonstrates marking partition centre lines and face lines on floors and ceilings from drawings. Accurate face-line marking prevents cumulative dimensional errors.

Lesson 3 • Setting Out for Openings and Services

Covers layout of door frames, window openings, and service penetration locations within partitions. Coordinated setting out prevents clashes with mechanical and electrical systems.

Lesson 1 • Framing Door and Window Openings

Teaches installation of headers, king studs, and jack studs for door and window openings. Correctly framed openings support door frames and prevent board cracking.

Lesson 2 • Framing for Services and Fixtures

Addresses blocking, backing, and reinforced framing for fixtures, cabinets, and service penetrations. Pre-installed backing eliminates costly remediation after boarding.

Lesson 3 • Installing Floor and Ceiling Tracks

Covers fastening floor and ceiling tracks to structural substrates at correct positions. Properly anchored tracks provide the rigid base for all vertical framing members.

Lesson 4 • Bracing and Structural Connections

Covers horizontal bridging, diagonal bracing, and connections to structural elements. Adequate bracing prevents racking and ensures long-term partition stability.

Lesson 1 • Defect Identification and Remediation

Identifies common defects including ridging, blistering, and fastener pops and their causes. Systematic defect diagnosis and repair ensures surfaces meet quality standards.

Lesson 2 • Taping and Jointing Techniques

Demonstrates paper tape, mesh tape, and pre-mixed compound application for seamless joints. Proper taping technique is the primary determinant of final surface quality.

Lesson 3 • Board Fixing and Screw Patterns

Covers board orientation, staggered joint layout, and screw spacing for single and double layers. Correct fixing patterns prevent fastener pops and structural weakness.

Lesson 4 • Sanding and Surface Preparation

Covers wet sanding, dry sanding, and skim coat application to achieve Level 4 and Level 5 finishes. Surface preparation quality directly determines paint and wallcovering adhesion.

Lesson 1 • Acoustic Performance Fundamentals

Introduces STC ratings, flanking paths, and acoustic design principles for partition assemblies. Acoustic knowledge guides material and detail selection to meet performance targets.

Lesson 2 • Fire Resistance Principles and Ratings

Explains fire resistance rating concepts, tested assembly requirements, and regulatory compliance. Understanding ratings enables correct assembly selection and documentation.

Lesson 3 • Installing Fire-Rated Assemblies

Covers construction of fire-rated stud wall assemblies including board layers and fastener schedules. Strict adherence to tested assembly details is mandatory for rating validity.

Lesson 4 • Firestopping Penetrations and Joints

Teaches approved firestop methods for pipes, conduits, ducts, and construction joints. Unprotected penetrations void fire ratings and create life-safety hazards.

Lesson 1 • Glazed and Frameless Partition Systems

Teaches installation of framed and frameless glass partition systems including hardware and seals. Glass systems demand precise structural support and watertight detailing.

Lesson 2 • Quality Assurance and Commissioning

Establishes inspection, testing, and handover procedures for completed partition installations. Systematic commissioning confirms performance compliance before project handover.

Lesson 3 • Curved and Radius Partition Construction

Demonstrates techniques for constructing curved partitions using kerfed board and flexible track. Radius work requires specialised layout and incremental forming methods.

Lesson 4 • Movable and Operable Wall Systems

Addresses installation of top-hung and bottom-rolling operable wall systems and their hardware. Correct track alignment and panel sequencing ensure smooth, gap-free operation.